Raspberry Pi Infragram
raspberry-pi-infragram

This page collects research on using #raspberry-pi based cameras (aka #pi-camera) to take [Infragram](/wiki/infragram) multispectral photos, for plant health analysis. It is supported in part by the [AREN project at NASA](/aren). ## Design goals Low cost, low complexity, easy to build and open source! Also see the [Image Sequencer](/image-sequencer) project which is designed to run on a Raspberry Pi for on-board image processing. To get a kit with this already set up on an SD card and/or Raspberry Pi camera, see: * [Infragram Pi Camera Kit](https://store.publiclab.org/products/infragram-pi-camera) * [Pre-flashed SD cards for Raspberry Pi cameras](https://store.publiclab.org/products/pi-builder-cards) ## Quick start [notes:grid:activity:pi-camera-setup] If yours is already assembled, just plug it in using a Micro USB cable (or battery pack) and it'll create a WiFi network called `00-PiCamera` -- password `publiclab` -- which you can log into from your phone or laptop. You'll quickly see streaming video, be able to take photos, timelapses, or videos, do motion triggered capture, and more. ## Questions Questions can be either frequently asked questions, or "next step" challenges we're looking to solve. [questions:raspberry-pi-infragram] ## Activities Activities show how to use this project, step by step. [activities:raspberry-pi-infragram] ...


Author Comment Last activity Moderation
a1ahna "@marliespo @JorgeHM Hey y'all! Sorry for the late reply. If you're able to connect to the wifi with password "publiclab" and you see the pi.loca..." | Read more » 10 months ago
JorgeHM "Hello guys, It been a while, I would like to know if there are any comments about this problem. What if I reset the SD card a install the program..." | Read more » about 1 year ago
bhamster "Sorry to hear about these issues with getting a video feed. @a1ahna, do you have any other tips or tricks to try? " | Read more » about 1 year ago
marliespoe "Hey! I just ordered a pre-assembled infragram camera and i have the same problem as jorgehm. i checked the ribbon cable - no result. any other solu..." | Read more » about 1 year ago
JorgeHM "Hello mimiss, Thanks for your reply. I tried what you suggest, but it didn't solve the problem. Any other idea to solve this issue? " | Read more » over 1 year ago
mimiss "@JorgeHM, how is the connecting of the camera lens to the circuitboard? I've gotten this error before when that was loose. to check this, you'll ne..." | Read more » over 1 year ago
JorgeHM "Hello guys, @warren @amocorro @purl @mimiss Any idea of what is happening? I'll be thankful if you can help to solve this issue. Regards, " | Read more » over 1 year ago
JorgeHM "Hi @warren, thanks for your reply. I checked the ribbon cable and it's look OK, but I installed again anyways, following the intructions in the tut..." | Read more » over 1 year ago
warren "Hi @JorgeHM the most common reason for this is the ribbon cable being inserted backwards (it's quite confusing, both ends could be reversed so 4 po..." | Read more » over 1 year ago
JorgeHM "Thanks @amocorro I'm looking forward to use this camera. " | Read more » over 1 year ago
amocorro "@jorgehm thanks for your question. It's always so frustrating when technology glitches occur. I've gone ahead and added some additional tags to you..." | Read more » over 1 year ago
liz "This is super! very useful thank you " | Read more » almost 2 years ago
xose "@xose awards a barnstar to wln215 for their awesome contribution! " | Read more » almost 2 years ago
xose "Awesome! " | Read more » almost 2 years ago
amazinggames413 "This is Very very nice article. Everyone should read. Thanks for sharing and I found it very helpful. Don't miss WORLD'S BEST GAMES " | Read more » about 3 years ago
tech4gt " @MaggPi Try it with sudo! I think global packages need to be installed with root user access now! sudo npm i -g image-sequencer " | Read more » about 3 years ago
MaggPi "I did this! but I seem to get an access error. Is there a permission necessary? Thank You pi@raspberrypi:~ $ npm install -g image-sequencer npm W..." | Read more » about 3 years ago
jenjimah " Hi Warren, Sure I'd be happy to try to add that in, it's only 2 files that need to be updated after all. However before that, there are a few thin..." | Read more » about 3 years ago
warren " This is great! Indeed, this is a good approach, although I found that not all computers could use an internet gadget either without drivers, it's ..." | Read more » about 3 years ago
jenjimah "I did this! Hardware: Raspberry Pi Zero W Software: Raspbian Stretch Lite, Windows 10 (on PC) Connection: USB configured as ethernet device; SSH i..." | Read more » about 3 years ago
jenjimah " Thanks for the link! I also wasn't able to use the wifi method of connecting so I also connected over usb. I had to follow the whole tutorial from..." | Read more » about 3 years ago
warren "We now have a great solution for this! https://publiclab.org/infrapi !! and a kit available there. " | Read more » almost 4 years ago
warren "Glad to hear it. I've noted that not all WiFi networks work, and sometimes trying on a different one (like the one I broadcast from my phone) works..." | Read more » about 4 years ago
Aleksi12358 "I managed to connect with usb. Now I will try to get camera to work and calibrate my spectrometer. I followed this: https://learn.adafruit.com/turn..." | Read more » about 4 years ago